原因你一定不會成功，它平的理由之一是 你要做埋 QC個份工…
你要在 YOUTUBE 找它的TURN 機教學一步步咁 TURN 好部機先，
以下是小弟多次失敗後的經驗總結：
1） 鏍絲不要太緊，啱啱好就得
2） X Y 軸 試行到，不要搖晃（這個得重要）
3）印床要好好調較，要平均，熱頭同印床的距離要啱啱比到一張咭片厚度過，好以有少少拉到的感覺（太近會塞頭，太遠印唔到）看番官方教學
之後要落多D 雪油（五金店有賣）係 X Y Z 的鏍絲 軸 ，印頭的軸等（小心不要令印頭碰到雪油）
完成以上的基本野你就可以試印，看看熱頭有沒有印得不平均，出膠有沒有問題。
基本會遇到的問題：
出唔到膠 ﹣ 開了機 PRINT 出膠STEPPER 係咁轉但出唔到膠，
看看STEPPER 有沒有粉跌出，有就是膠修頂著出不了膠磨去了膠修
有三種可能：
1）熱頭唔夠熱，MAKIBOX 的PLA 熱度我通常是 194度既（不要用手試，燙手很傻的）
2）熱頭之上的鐵管過熱，令到膠未到熱頭就漲滿整條鐵管，做成塞管。（解決方法是加風扇，在下一篇將會出教學）
3） 膠條的頭，卡在候管的接位裏（解決方法是斜剪膠條的頭）
另外印件是否成功，其中重要的部份在SLIC3R的G﹣CODE 有關，記得用官方的 SETTING
（千其唔好用內置SETTING）
以下是我改了少少的SETTING，比大家參考：
# generated by Makible Ltd. A6 LT （只是PLA ONLY）
avoid_crossing_perimeters = 0
bed_size = 110,150
bed_temperature = 0
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_fan_speed = 0
bridge_flow_ratio = 1
bridge_speed = 50
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off hot end\nM140 S0 ; turn off hot bed\nG92 E0 ; set E value to 0 at current position\nG1 F1000 X0 Y0 E-15 ; 1000mm/min speed of print head, 15mm filament to retract\nG92 E0 ; set E value to 0 at current position\nM84 ; disable motors
external_perimeter_speed = 35
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 0.3
fill_pattern = rectilinear
first_layer_bed_temperature = 0
first_layer_extrusion_width = 200%
first_layer_height = 150%
first_layer_speed = 20
first_layer_temperature = 193
g0 = 0
gap_fill_speed = 25
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 45
layer_gcode =
layer_height = .2
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 15
notes =
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 1
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 2
post_process =
print_center = 55,75
raft_layers = 0
randomize_start = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 4
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 70
rotate = 0
scale = 1
skirt_distance = 4
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 30
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 45
spiral_vase = 0
start_gcode = G28 ; home all axes\nM109 S[first_layer_temperature] ; heat up hot end to set temperature\nM82 ; use absolute distances for extrusion\nG90 ; use absolute coordinates\nG92 E0 ; set E value to 0 at current position\nG1 F500 E35 ; 500mm/min speed of print head, 35mm filament to extrude\nG92 E0 ; set E value to 0 at current position
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.65
support_material_interface_layers = 0.65
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 45
support_material_threshold = 0
temperature = 194
threads = 2
toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 35
top_solid_layers = 5
travel_speed = 55
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0
同部機搏鬥了三個星期終於可以 PRINT 到少少似樣既野…
（待續）
沒有留言:
張貼留言